|
HSV-300
U.S. DOLLAR BILL ACCEPTOR
|
HSV-300
OPERATING MANUAL
INSTALLATION INSTRUCTIONS
FOR
U. S. DOLLAR ACCEPTOR
MODEL DBV-SUPER |
|
INSTALLATION
NOTES
- THESE INSTRUCTIONS CAN BE USED IN HSV-300
KITS. REFER TO THE PARTS LIST IN THIS INSTRUCTION SHEET FOR A BREAKDOWN
OF THE PARTS CONTAINED IN YOUR PARTICULAR KIT.
- DUE TO THE VARIETY OF VIDEO GAME DESIGNS,
THIS BILL ACCEPTOR WILL NOT OPERATE IN ALL VIDEO GAMES.
- THE BILL ACCEPTOR SHOULD BE ELECTORICALLY
CONNECTED TO YOUR GAME AND TESTED BEFORE FINAL INSTALLATION IS
ATTEMPTED.
- DESIGNATE NUMBER OF BILL TO BE
INSERTED ACCORDING TO MAXIMUM CREDITS OF VIDEO GAME, IT IS NECESSARY TO
INPUT INHIBIT SIGNAL IN CASE OF EXCEEDING MAXIMUM CREDIT OF VIDEO
GAMES.
- THIS BILL ACCEPTOR INSTALLATION REQUIRES
A MOUNTING HOLE IN THE VIDEO GAME CABINET.
-
SINCE MANY VARIATIONS IN
CABINET CONSTRUCTION AND SIZE EXIST, NO BILL STACKER IS PROVIDED IN THIS
KIT. YOU MUST PROVIDE A BILL BOX OR OTHER SUITABLE
CONTAINER. |
INSTALLATION
- INSTALLATION OF BILL ACCEPTOR.
A) SET THE BILL ACCEPTOR ON FACE PLATE AND TIGHTEN THE
SCREW M3 X 8.
B) INSTALL THE BILL ACCEPTOR WITH FACE PLATE ON THE DOOR
OF VIDEO GAME MACHINE.
- HOW TO OPEN UPPER COVER.
A) LOOSE THE SCREW (M3 X 8) LOCATED ON THE BOTTOM OF
BILL ACCEPTOR.
B) SLIDE THE BILL ACCEPTOR BACKWARD.
C) LOOSE THE SCREW ON THE TOP COVER TO OPEN.
- HOW TO REMOVE THE COVER.
|
| FUNCTION SWITCHES
1,2,3,4,5,6,7, AND 8
THESE EIGHT SWITCHES DETERMINE THE NUMBER OF CREDIT PULSE
AND THE DURATION OF A CREDIT PULSE. THE DIP SWITCHES ARE LOCATED ON CPU
BOARD OF BILL ACCEPTOR.
*NOTE: IF ANY CHANGE IS MADE IN FUNCTION SWITCHES
1 THROUGH 8'S SETTING. POWER MUST BE DISCONNECTED AND RECONNECTED TO MAKE
THE CHANGE EFFECTIVE.
| SW1 |
SW2 |
SW3 |
1US$-PULSE |
| 1 |
1 |
1 |
1 : 1 |
| 0 |
1 |
1 |
1 : 2 |
| 1 |
0 |
1 |
1 : 3 |
| 0 |
0 |
1 |
1 : 4 |
| 1 |
1 |
0 |
1 : 5 |
| 0 |
1 |
0 |
1 : 10 |
| 1 |
0 |
0 |
1 : 20 |
| 0 |
0 |
0 |
1 :
100 |
A) DIP SW. 1,2 AND 3
THE DIP-SW 1,2 AND 3 DETERMINE THE NUMBER OF CREDIT
PULSE PRODUCED PER DOLLAR ACCEPTED. A $1 BILL WILL PRODUCE THE NUMBER
OF PULSE SELECTED AND A $5 BILL WILL PRODUCE FIVE TIMES THE NUMBER OF
PULSE SELECTED. IN VIDEO GAME THESE PULSE ARE APPLIED TO THE COIN
SWITCH AND MAY BE CONSIDERED AS QUARTER EQUIVALENTS. WITH THESE TWO
SWITCHES OFF, THE BILL ACCEPTOR ALWAYS PRODUCES ONE PULSE. THE TABLE 1
SHOWS THAT THE BILL ACCEPTOR CAN BE PROGRAMMED POR ONE TO FOUR PULSES
PER DOLLAR.
B) DIP-SW-4 & 5
THESE SWITCHES DETERMINES DURATION OF A CREDIT PULSE
AND THE SPACING BETWEEN THE PULSES.
| SW4 |
PULSE |
| 1 |
50MS |
50MS |
| 0 |
300MS |
50MS |
| SW5 |
INHIBIT |
| 1 |
ACTIVE LOW |
| 0 |
ACTIVE
HIGH |
|
| PRE-INSTALLATION
STEPS
TAKE FOLLOWING STEPS BEFORE YOU ACTUALLY INSTALL BILL
ACCEPTOR WITH YOUR GAMING MACHINE.
- CONNECT HARNESS FROM ACCEPTOR TO GAME MACHINE.
- TURN THE POWER "ON" AND CHECK IF THE POWER LED IS LIT
(GREEN LED SHOULD BE LIT)
- INSERT 1 DOLLAR AND 5 DOLLAR BANKNOTE.
- IF ACCEPTANCE RATE OF BILL IS LOW, CHECK FOLLOWING
POINTS:
- OPEN THE TOP COVER AND CHECK:
- TRANSPORT BELT TIGHTNESS
- FEED ROLLER ROTATION
- DUST, MOISTURE, IRON FILINGS ON THE SENSORS OR
TRANSPORT BELT
- ANTI PULL BACK LEVER MOVES SMOOTHLY
- THE INTERFACE IS PROPERLY CONNECTED.
- THE INHIBIT SIGNAL (INH) IS ACTIVE? WIPE OFF THE
SURFACE OF TRANSPORT AND SENSOR AREA BY A PIECE OF CLOTH WITH
ALCOHOL.
|
| INTERFACE
CONNECTOR FT-27
TERMINAL FT-29
- OUTPUT SIGNAL
THE OUTPUT SIGNAL OF OUTSIDE INTERFACE IS VENDOR SIGNAL.
THIS SIGNAL IS LO ACTIVE. THIS SIGNAL OUTPUTS PULSE FOR ALL BILLS
ACCEPTOR.
- INPUT SIGNAL
THE INPUT SIGNAL OF OUTSIDE INTERFACE IS INHIBIT (INH)
SIGNAL. THIS SIGNAL IS HI ACTIVE. THIS SIGNAL INHIBITS TO ACCEPT
BILLS.
PARTS LIST
1.HSV-300 BILL ACCEPTOR
2.METAL FACE
PLATE
3.INTERFACE CABLE
4.TEMPLATE
US $ 1, 5, 10, 20, 50, 100 BILL
110 VOLT ADAPTER
AVAILABLE |
|
 
|
